For the past many years, there have been many forms of the game of pool in existence. The fact that there have been various changes to the materials that the game is comprised has not had an effect on the felt cover. It is one aspect that has remained the same over time. However, it has a short lifetime that means it has to be replaced over and over after some time. In consideration of pool table refelting Denver residents should be acquainted with the basic of the procedure.
Among the materials required for the replacement are a socket wrench, felts, rag, cleanser, staple gun and hammer. For a start, the staples surrounding the pockets towards the underside of the table will need to be removed. This is followed by removing the rails securing the underside through the use of a socket wrench. Approximately, the individual will need to locate three bolts for every rail.
After removal of all the bolts, the rails are taken off. There is then detachment of the pocket liners as is necessary. When this has been done, the staples that are attached the felt to rail cushions will need to be pulled out. The felt that covers the cushions can then be removed with ease, after which it is removed. One needs to know whether the felt is glued or stapled, or both. Pulling of the individual staples from the felt is done using a staple puller. It is important to be very gentle when peeling the glued felt from the top of the table.
It will be then time to prepare the slate for re-felting. Pool table wax is used for filling in all holes and cracks. After letting the wax harden for one minute, the excess gets scrapped off using a putty knife. A gentle cleanser is then used for cleaning the surface of the slate. Before getting covered with the felt, the surface has to be left to dry completely.
The felt pieces that will be used have to be properly and accurately measured. This is followed by cutting them in accordance to the table dimensions. Failure to do the measurements and cutting accurately will lead to the table having an undesirable appearance.
After making the measurements and doing the cutting, the fabric will need to be stapled to the table. This is started from the center of any short edge and moving gradually towards the corners. During all this, the pockets ought not to be covered. During placement of the staples, the person doing the work should move in increments of roughly two inches as the fabric is pulled taut. This happens for all table sides.
There is trimming of excess fabric from the pockets. On an approximate basis, three inches of the fabric are left at the inner edges. What follows is pushing of the fabric to the pockets such that all pocket sides are lined.
There is wrapping of the rails with felt. It would be vital to observe the unique design of the rails so as to determine the size of felt pieces to use. The rails are attached to the table, and then the liners and pockets are replaced accordingly.
Among the materials required for the replacement are a socket wrench, felts, rag, cleanser, staple gun and hammer. For a start, the staples surrounding the pockets towards the underside of the table will need to be removed. This is followed by removing the rails securing the underside through the use of a socket wrench. Approximately, the individual will need to locate three bolts for every rail.
After removal of all the bolts, the rails are taken off. There is then detachment of the pocket liners as is necessary. When this has been done, the staples that are attached the felt to rail cushions will need to be pulled out. The felt that covers the cushions can then be removed with ease, after which it is removed. One needs to know whether the felt is glued or stapled, or both. Pulling of the individual staples from the felt is done using a staple puller. It is important to be very gentle when peeling the glued felt from the top of the table.
It will be then time to prepare the slate for re-felting. Pool table wax is used for filling in all holes and cracks. After letting the wax harden for one minute, the excess gets scrapped off using a putty knife. A gentle cleanser is then used for cleaning the surface of the slate. Before getting covered with the felt, the surface has to be left to dry completely.
The felt pieces that will be used have to be properly and accurately measured. This is followed by cutting them in accordance to the table dimensions. Failure to do the measurements and cutting accurately will lead to the table having an undesirable appearance.
After making the measurements and doing the cutting, the fabric will need to be stapled to the table. This is started from the center of any short edge and moving gradually towards the corners. During all this, the pockets ought not to be covered. During placement of the staples, the person doing the work should move in increments of roughly two inches as the fabric is pulled taut. This happens for all table sides.
There is trimming of excess fabric from the pockets. On an approximate basis, three inches of the fabric are left at the inner edges. What follows is pushing of the fabric to the pockets such that all pocket sides are lined.
There is wrapping of the rails with felt. It would be vital to observe the unique design of the rails so as to determine the size of felt pieces to use. The rails are attached to the table, and then the liners and pockets are replaced accordingly.
About the Author:
Find a review of the advantages of hiring a provider of pool table refelting Denver services and more information about a reliable service provider at http://www.anytimebilliards.com now.
0 nhận xét:
Đăng nhận xét